Home Uncategorized What is the reason for the printer’s slow response?

What is the reason for the printer’s slow response?

by admin

What is the reason for the printer’s slow response? My printer is T10. I can’t respond to printing for half a day?

fault phenomenon: when the printer performs printing, the printing speed is very slow, or the response of the printer is very slow after sending the printing task, and even printing the internal test page is very slow. At the same time, during printing, the ink cartridge stays on the left or right side of the printer for a long time

solution:

1. Check the ink cartridge

remove the ink cartridge from the printer. Clean the Yellow contacts on the back of the ink cartridge with a clean, soft, lint free cloth. Press the play button once to see the operation process of cleaning the metal contacts on the back of the ink cartridge. Reinstall the ink cartridge to ensure that the ink cartridge is properly placed in the ink cartridge base and in good contact

2. Change print settings

3. Print the online test page

4. Refresh the USB port

5. Replace the USB cable

after sending the print task, if the printer responds very slowly, there is usually a problem in data communication. At this time, it is recommended to replace the USB cable and try printing again to check whether the printing speed returns to normal. If the printing speed returns to normal, it indicates that the problem has been solved and the printer can be used normally

extended data:

printer fault diagnosis and maintenance:

1. The printer has printing action, but cannot print characters

diagnosis and treatment: This is because there is a problem with the printer nozzle, which may be the improper installation of the nozzle. It is recommended to remove the print nozzle first and then reinstall it

2. The printer has printing action, but there is a defect in printing characters. Less stroke

diagnosis and treatment method: open the top cover in the shutdown state, and then remove the nozzle. Use absorbent cotton dipped in alcohol to gently scrub the contact surface between the nozzle and the base, and install the nozzle after the alcohol volatilizes

3. Send multiple sheets of printing paper at one time during printing

diagnosis and treatment method: if the printing paper does not meet the requirements, stick the paper together, separate the stuck paper and reload it. Remove some paper from the in tray

4. The printer cannot pick up the paper in the paper box and paper jam

diagnosis and treatment method: if the paper in the paper box is not attached to the paper feeder, push the printing paper inward. The paper is wrinkled, curled or the edge of the paper is not neat, so that the paper is clamped in the printer and there is a paper jam

the printer’s response is slow because the printer has entered “spooling printing”. Just reset the printer. The specific operation steps are as follows:

1. First, open the “control panel” on the computer desktop, as shown in the figure below

2. Secondly, select the “device and printer” option, as shown in the figure below

3. Right click the printer and select “printer properties”, as shown in the following figure

4. Then, select the “share” option in the “properties” dialog box to ensure that the printer is in the shared state, as shown in the following figure

5. Then, select the “advanced” option in the “properties” window, as shown in the following figure

6. Finally, in the open dialog box, check whether the radio button “use background printing so that the program can end printing faster” is selected. If yes, it means that the printer has started “spool printing”, and cancel it, as shown in the following figure

the slow response of the printer is because the printer has entered “spool printing”. Just reset the printer

tools to be prepared: computer, printer

1. First open the control panel on the desktop

2. Select a device and printer

3. Right click the printer and select printer properties

4. Select the second [share] option in the “properties” dialog box to ensure that the printer is in the shared state

5. Select the [advanced] option in the “attribute” window

6. Check whether the radio button [print in the background so that the program can print quickly] is selected in the open dialog box. If it is selected, it indicates that the printer has started “spool printing” and can be solved by canceling

go to Baidu app to view
Answer

 Hello, I have seen your question and am sorting out the answers. Please wait a moment ~ 

 the reasons why the printer is slow are: 

 1. The printer should be preheated evenly before printing

 2. Print data transmission and check whether there is a problem with the print line

 3. There is a quality option in the printing preference in the driver, which distinguishes the printing quality. Generally, the higher the printing quality, the slower the printing speed

 4. There is a problem with the printer, which may be due to poor heating components. 

Ask

 how to deal with 

Answer

 check the above faults first

6 more

there are three reasons for this: 1. It is the problem of your computer itself, which is generally not very likely. 2. It is the problem of data parameters when the computer is transmitted to the printer. What interface do you use? Serial port, parallel port or USB. It is recommended to use USB port or parallel port. In this way, the data flow accepted by the printer will be much larger. 3. It’s the memory problem of the printer itself. If the memory of the printer itself is small, when you print something with a lot of content, and the memory and cache of the printer are relatively large, you will also encounter the problem of missing printed content.

Related Posts

Leave a Comment